Celestron 50TT Refractor Telescope Instructions: A Step-by-Step Setup Guide
Celestron 50TT refractor telescope instructions explained step by step: assembly, eyepiece use, finding your first target, and simple tips for young stargazers.
Updated November 2026
Celestron 50TT refractor telescope instructions boil down to a few clear stages: assemble the tripod and optical tube, insert an eyepiece, aim at an easy daytime target to focus, and then move to the night sky. This guide walks you through each stage so you can have your first views of the Moon and planets in under an hour. Exact part names may vary slightly between printings, so check the manual packed with your telescope if anything looks different.
Assembling the Tripod and Optical Tube
Start by spreading the tripod legs fully and tightening the leg locks. Set the tripod on flat ground, then attach the mount head and tighten the center bolt by hand. Slide the optical tube onto the mount and fasten it with the tube clamp so it sits level and does not wobble.
Shopping for one? See our guide: Reflector or Refractor Telescope for Beginner: Which Should You Choose?.
- Extend each tripod leg to a comfortable height for the person using the telescope.
- Thread the accessory tray onto the tripod, if your kit includes one.
- Attach the optical tube to the mount and secure all knobs.
- Check that the altitude and azimuth controls move smoothly before you go outside.
Inserting the Eyepiece and Finderscope
The 50TT comes with a low-power eyepiece, usually used first because it gives the widest view and is easiest to point. Loosen the eyepiece holder thumbscrew, insert the eyepiece barrel into the focuser drawtube, and tighten the screw until it is snug. Next, align the finderscope with the main tube. Look through the finder at a distant object, such as a rooftop or tree, and adjust its small screws until that object sits in the crosshairs.
Focusing on a Daytime Target
Focusing is easier in daylight than at night because you can see detail clearly. Point the telescope at a distant object at least a few hundred yards away and never at the Sun. Turn the focus knob slowly in one direction until the image blurs, then reverse direction until it sharpens. Once it is crisp, you are ready to look at the sky.
Safety Reminder
Never look at or near the Sun through any telescope or finderscope without a proper solar filter, because direct sunlight can cause permanent eye damage. Keep the lens cap on or the telescope covered when you are not observing. Adults should supervise younger children during setup.
Finding Your First Night Sky Target
Begin with the Moon, which is bright, easy to locate, and shows craters and shadows well. Use the finderscope to center the Moon, then look through the eyepiece and refine the focus. After that, try bright planets such as Jupiter or Venus, which look like small disks or bright points. Star charts or a free stargazing app help you match what you see to the sky.
Recommended Gear
- Red-light headlamp: Preserves your night vision while you read star charts and adjust the telescope. View on Amazon
- Planisphere star wheel: A rotating star chart that shows what is overhead for a given date and time. View on Amazon
- Eyepiece set: Additional eyepieces let you change magnification for planets and the Moon. View on Amazon
Common Mistakes and Tips
- Setting up the tripod on soft or uneven ground, which causes shaky views.
- Starting with the highest-power eyepiece, which makes objects hard to find and blurry.
- Forgetting to let your eyes adjust to the dark for about 15 to 20 minutes.
- Skipping the finderscope alignment, which wastes time searching for targets.
- Touching the optics with bare fingers. Use a soft lens brush if dust appears.
FAQ
How long does it take to set up the Celestron 50TT?
Most first-time setups take 20 to 30 minutes once you know the steps. Practice indoors during daylight to save time at night.
Which eyepiece should I use first?
Start with the low-power eyepiece included with the telescope. It offers a wide field of view and makes it easier to locate targets.
Can I use the 50TT to look at the Sun?
Not without a certified solar filter placed over the front of the telescope. Never look at the Sun through any optical instrument without one, as it can cause serious eye injury.
Conclusion
With the tripod assembled, the eyepiece in place, and the finderscope aligned, the Celestron 50TT is ready for its first night out. Begin with the Moon and bright planets, then build your skills from there. Clear skies and patient practice will turn these simple steps into a lasting family hobby.
Related reading
- Celestron Starsense Explorer Lt 80az Refractor Telescope: A Practical Guide (2026)
- Celestron Starsense Explorer Dx 102az Refractor Telescope: A Practical Guide (2026)
- Celestron StarSense Explorer LT Refractor Telescope: Setup, Use & Tips (2026)
- Celestron Inspire 100AZ Refractor Telescope: Setup, Use and Tips for Families
- Celestron AstroMaster 70AZ Refractor Telescope: Setup, Use and Tips (2026)
- Which Refractor Telescope for Planets Should Families Buy? Key Factors
Ready to choose one?
