We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

3D Solar System Model on Poster Board: A Step-by-Step Guide for Kids

Learn how to build a 3D solar system model on poster board with simple materials, planet sizing tips, and easy steps kids can follow at home or in class.

Updated November 2026

A 3D solar system model on poster board is one of the easiest school and family projects to build. In this guide, you will learn how to lay out the sun and planets to scale, attach them so they stand out from the board, and label them clearly. Most of the work takes an afternoon, and it needs only basic supplies you probably already have.

Gather Your Materials

You do not need specialty tools for this project. Plan for one sturdy poster board, which is the base, and a few materials to build the planets.

Shopping for one? See our guide: 4 Best Hanging Solar System Model Kits for Kids (2026).

  • One piece of foam board or thick poster board, at least 22 by 28 inches
  • Round objects for planets, such as foam balls, cardboard circles, or paper-mache spheres
  • Craft paint or markers and a small brush
  • Hot glue or strong craft glue, plus tape
  • Pipe cleaners, skewers, or bamboo sticks for supports
  • A ruler, pencil, and a printed size chart

Plan the Sizes and Distances

A true scale model of the solar system would not fit on any poster, because the distances are huge. Instead, most families scale the planet sizes and then shrink the spacing to fit the board. Keep the sizes proportional to each other, even if the distances are compressed.

Start with the sun, then pick a diameter for Earth. Use this rough ratio to size the others: Jupiter is about 11 times wider than Earth, Saturn about 9.5 times, and Mars about half of Earth’s width. Mercury, Venus, Uranus, and Neptune fall in between. Tiny Pluto is usually shown as the smallest object, or left out if your teacher requires only the eight planets.

Set Your Spacing

Place the sun at the center of the board or along the left edge. Mark orbit lines with a pencil using a compass or a string tied to a pen. Keep the inner planets close together and let the outer planets spread farther out. Add a note on the board explaining that distances are not to scale.

Build and Attach the Planets

  1. Paint each sphere in its real color. Earth is blue and green, Mars is red-orange, Jupiter has pale bands, and Saturn needs a flat ring cut from cardboard.
  2. Let the paint dry fully before handling. Thin coats dry faster and look cleaner.
  3. Push a skewer or pipe cleaner into the base of each planet so it stands off the board.
  4. Glue the other end of the support to the poster board at its marked spot. Use a small dab of glue, then hold for a minute while it sets.
  5. For a flatter look, glue the planets directly to the board and draw the orbit lines in pencil.

Label the Model Clearly

Write each planet’s name beneath or beside it in neat block letters. Add one or two facts, such as distance from the sun or length of a day. Include a title at the top and a key that explains your scale. Judges and teachers look for accurate labels as much as for a nice design.

Check Your Work

Step back and make sure the order from the sun outward is correct: Mercury, Venus, Earth, Mars, Jupiter, Saturn, Uranus, Neptune. Confirm the sizes look right relative to one another, then fix any mistakes before the glue sets.

Common Mistakes

  • Making every planet the same size, which hides the difference between small rocky worlds and giant gas planets.
  • Putting the sun too close to the edge, leaving no room for the outer planets.
  • Using heavy planets on thin supports, so they tip over.
  • Skipping the scale note, which can confuse anyone reading the board.
  • Painting before the base is dry, causing smudges and warped spots.

A stiff foam board holds up better than thin poster board when you add 3D planets. View on Amazon

Lightweight foam balls in several sizes make planet scaling much easier. View on Amazon

Thin wooden dowels or bamboo skewers give planets clean, steady supports. View on Amazon

FAQ

Do the planets have to be to scale?

Sizes should be proportional to each other, but distances can be compressed to fit the board. Most classroom rubrics accept this as long as you label the scale.

Can I use poster board for the planets too?

You can cut circles from poster board and layer them to make rounded planets, though foam balls are sturdier and easier to paint.

Which planet should be the largest?

Jupiter is the largest planet, followed by Saturn. Make the sun much bigger than any planet if you have room.

Conclusion

A 3D solar system model on poster board comes together quickly once you plan the sizes and spacing. Keep the planets proportional, attach them securely, and label everything clearly. Your finished board will show the order and relative size of the planets in a way that is easy to understand.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our astronomy for kids, teens & families guides, checking product details against manufacturer specifications and owner feedback.

About the author

Emily Parker
Emily Parker

Emily Parker writes reviews and buying guides for Youth in Astronomy.