We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Binocular Phone Mount 3D Print: A Step-by-Step Guide for Young Stargazers

Learn how to 3D print a binocular phone mount for steady night-sky photos. Covers design fit, print settings, assembly and tips for young stargazers.

Updated November 2026

A binocular phone mount 3D print lets you hold a phone steady at the eyepiece and capture the Moon, star clusters and bright planets without shaky blur. This guide walks you through choosing a design, setting up your printer, and checking the fit so the mount works the first time. Most families can finish a basic version in an afternoon of printing and a few minutes of assembly.

Choose a Design That Fits Your Binoculars

Before you open any file, measure the barrel of your binoculars where a mount would clamp. Common designs grip either the central hinge or the eyepiece barrel, so check which one your model allows. Look for a printable design that lists its compatible binocular sizes, and avoid files that only say “universal” without dimensions. Our guide on Binocular Mobile Phone Mount: How to Photograph the Night Sky Steadily explains how a phone holder should line up with the eyepiece.

Shopping for one? See our guide: 4 Best Farpoint Universal Binocular Mount Options Compared (2026).

Strength matters more than appearance here, because the mount carries the weight of a phone and must resist flexing. Use settings that favor a solid part:

  • Layer height of 0.2 mm for a good balance of detail and speed
  • At least 4 perimeter walls and 30 to 40 percent infill
  • PLA for easy printing, or PETG if the mount will sit in a warm car
  • Print clamp arms flat on the bed to keep layer lines running along the grip

Manufacturers of common printer filaments generally recommend drying filament that has absorbed moisture, since damp filament can print weak and stringy parts.

Test the Fit and Assemble

Print a small test piece of the clamp first if your printer has been running a new filament. Slide it onto the binocular barrel and check that it grips without cracking. If it is loose, reduce the clamp radius by about 0.2 mm in your slicer and reprint. Once the clamp fits, attach the phone holder arm, tighten all fasteners by hand, and check that the phone sits centered over the eyepiece.

Align the Phone With the Eyepiece

Center the phone camera lens over one eyepiece while looking through the other. Tilt the holder until the image is level, then lock it. A small misalignment will show up as a dark crescent in your photos, so take a few test shots of the Moon before a real session.

Checklist for Your First Build

  1. Measure the binocular barrel diameter
  2. Choose a design with listed compatible sizes
  3. Print one test clamp
  4. Print the full mount with at least four walls
  5. Assemble with hand-tight fasteners
  6. Test-shoot the Moon before a full session

Common Mistakes

  • Skipping the test print, which often wastes a full print run
  • Using too little infill, leaving clamp arms that bend under the phone’s weight
  • Tightening fasteners too hard and cracking thin plastic
  • Forgetting to level the phone, which tilts every photo
  • Printing with damp filament that prints brittle
  • Adjustable phone clip for binoculars helps you fine-tune alignment after printing, so you are not reprinting for small corrections. View on Amazon
  • Binocular tripod adapter keeps the rig steady during long exposures on a tripod. View on Amazon

FAQ

Do I need a special 3D printer for this project?

No. Most entry-level FDM printers can produce a sturdy mount using PLA or PETG. Check that your printer’s build plate is large enough for the part you choose.

Will a 3D printed mount damage my binoculars?

A well-fitted clamp with soft inner padding should not scratch the barrel. Test with a loose fit first and tighten gradually.

Which phone photos work best with this mount?

The Moon and bright planets are the easiest targets for beginners, because they need short exposures and little tracking. Deep-sky objects usually require a tripod and longer exposures.

Conclusion

A binocular phone mount you print yourself can give young stargazers steady, rewarding photos of the night sky. Measure carefully, print with sturdy settings, and test before every session. With a little patience, your first build will be ready for a clear night.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our astronomy for kids, teens & families guides, checking product details against manufacturer specifications and owner feedback.

About the author

Owen Palmer
Owen Palmer

Owen Palmer writes reviews and buying guides for Youth in Astronomy.